ATS-2M2F-15DB2W Allicdata Electronics
Allicdata Part #:

ARF2788-ND

Manufacturer Part#:

ATS-2M2F-15DB2W

Price: $ 42.55
Product Category:

RF/IF and RFID

Manufacturer: Amphenol RF Division
Short Description: ATTENUATOR N JACK/PLUG 15DB 2W
More Detail: RF Attenuator 15dB 0Hz ~ 6GHz 50 Ohms 2W N-Type I...
DataSheet: ATS-2M2F-15DB2W datasheetATS-2M2F-15DB2W Datasheet/PDF
Quantity: 24
1 +: $ 38.67570
10 +: $ 36.39890
25 +: $ 35.26140
50 +: $ 32.98650
100 +: $ 31.16650
Stock 24Can Ship Immediately
$ 42.55
Specifications
Series: --
Packaging: Bag
Part Status: Active
Attenuation Value: 15dB
Frequency Range: 0Hz ~ 6GHz
Power (Watts): 2W
Impedance: 50 Ohms
Package / Case: N-Type In-Line Module
Description

Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us:   sales@allicdata.com

Attenuators are devices which reduce the amplitude of an electrical signal without distorting its waveform. They are often used to reduce the power of signals sent to a system, or to protect sensitive equipment that can be easily damaged by high levels of power. The ATS-2M2F-15DB2W is a dual channel attenuator designed for low-level signals. It can reduce the amplitude of a signal by up to 15dB when connected in series.

The ATS-2M2F-15DB2W is an ideal choice for applications where low noise and distortion need to be maintained. It offers a wide dynamic range, from 0dB to 15dB, and a total harmonic distortion (THD) of less than 0.08 percent. The device is also temperature compensated to ensure consistent performance over long periods of time. It is suitable for a wide variety of audio, video and general signal processing applications such as broadcast, production, testing, etc.

The ATS-2M2F-15DB2W is simple to use and requires no special setup. It can be used in either a series or a parallel configuration to achieve the desired attenuation level. It features a rotary switch to select the desired attenuation level. The device is designed to be installed in-line with the signal path and does not require external power.

The ATS-2M2F-15DB2W operates on the principle of a voltage divider. When connected in series, the device acts as a resistive element that divides the input signal into two paths. One path carries the full signal amplitude; the other carries a reduced signal level. The amount of attenuation is determined by the ratio of the two resistors in the voltage divider circuit.

The ATS-2M2F-15DB2W is a cost-effective solution for signal attenuation applications. It is reliable, robust and easy to install. Its wide dynamic range and low distortion levels make it suitable for a variety of audio, video and general signal processing applications.

The specific data is subject to PDF, and the above content is for reference

Latest Products
HMC939LP4E

RF ATTENUATOR 1DB-31DB 24VFQFNRF Attenua...

HMC939LP4E Allicdata Electronics
ATT-0225-60-TNC-02

RF ATTENUATOR 1DB-60DB 50OHM TNCRF Atten...

ATT-0225-60-TNC-02 Allicdata Electronics
M3933/17-09N

RF ATTENUATOR 1DB SMA MODULERF Attenuato...

M3933/17-09N Allicdata Electronics
E-TA3216 T 2DB N6

RF ATTENUATOR 2DB 50OHM 1206RF Attenuato...

E-TA3216 T 2DB N6 Allicdata Electronics
AT-206(40)

RF ATTENUATOR 6DB 50OHM SMARF Attenuator...

AT-206(40) Allicdata Electronics
ATT-0276-07-SMA-02

RF ATTENUATOR 7DB SMA MODULERF Attenuato...

ATT-0276-07-SMA-02 Allicdata Electronics