![ATT-0313-15-BNC-10 Allicdata Electronics](https://files.allicdata.com/upload/common/default.jpg)
Allicdata Part #: | ATT-0313-15-BNC-10-ND |
Manufacturer Part#: |
ATT-0313-15-BNC-10 |
Price: | $ 0.00 |
Product Category: | RF/IF and RFID |
Manufacturer: | Cinch Connectivity Solutions Midwest Microwave |
Short Description: | ATTENUATOR 15 DB DC 4GHZ |
More Detail: | RF Attenuator 15dB ±0.75dB 0Hz ~ 4GHz 50 Ohms 2W B... |
DataSheet: | ![]() |
Quantity: | 1000 |
1 +: | 0.00000 |
Series: | -- |
Packaging: | Bulk |
Part Status: | Active |
Attenuation Value: | 15dB |
Frequency Range: | 0Hz ~ 4GHz |
Power (Watts): | 2W |
Impedance: | 50 Ohms |
Package / Case: | BNC In-Line Module |
Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us: sales@allicdata.com
Attenuators are electronic devices used to reduce voltage, power or current levels coming from one point to another in a circuit. The ATT-0313-15-BNC-10 attenuator is a type of attenuator commonly used in the radio frequency (RF) industry. It works by limiting the magnitude of the electrical signal passing through it.
Application Field
The ATT-0313-15-BNC-10 attenuator is primarily used in the radio frequency industry. Its main application is to reduce the signal strength of a signal before it enters into a receiver. This reduction of the signal is necessary in order to ensure that the receiver works correctly without being overloaded. By adjusting the attenuation level, the engineer can ensure that the signal is not too high or too low.
The ATT-0313-15-BNC-10 is also used in testing and measuring equipment in radio frequency electronics. It can be used to accurately measure and test signals. If connected to a spectrum analyzer or oscilloscope, the ATT-0313-15-BNC-10 can be used to measure signal levels coming into the circuit.
Working Principle
The ATT-0313-15-BNC-10 attenuator works on the same principle as other types of attenuators. It consists of a series of resistors connected in series to form a voltage divider. When an electric signal passes through the device, the voltage is divided proportionally across the resistors in the divider. The magnitude of the signal is then reduced or attenuated according to the settings of the attenuator.
The ATT-0313-15-BNC-10 attenuator also has an additional feature in the form of a high-pass filter. This filter works by allowing high frequency signals to pass through while attenuating lower frequency signals. This feature is useful in certain applications where only a certain range of frequencies is desired and other frequencies need to be filtered out. The filter can be adjusted to allow signals in a certain range to pass through and attenuate any signals outside of that range.
In summary, the ATT-0313-15-BNC-10 attenuator is a useful device used primarily in the radio frequency industry. It is used mainly to reduce the power levels of a signal before it enters into a receiver. It also has a high-pass filter which can be used to attenuate lower frequencies and pass higher frequencies. This allows it to be used for accurately measuring signal levels or outside of a certain range.
The specific data is subject to PDF, and the above content is for reference
RF ATTENUATOR 1DB-31DB 24VFQFNRF Attenua...
![HMC939LP4E Allicdata Electronics](https://files.allicdata.com/upload/common/default.jpg)
RF ATTENUATOR 1DB-60DB 50OHM TNCRF Atten...
![ATT-0225-60-TNC-02 Allicdata Electronics](https://files.allicdata.com/upload/common/default.jpg)
RF ATTENUATOR 1DB SMA MODULERF Attenuato...
![M3933/17-09N Allicdata Electronics](https://files.allicdata.com/upload/common/default.jpg)
RF ATTENUATOR 2DB 50OHM 1206RF Attenuato...
![E-TA3216 T 2DB N6 Allicdata Electronics](https://files.allicdata.com/upload/common/default.jpg)
RF ATTENUATOR 6DB 50OHM SMARF Attenuator...
![AT-206(40) Allicdata Electronics](https://files.allicdata.com/upload/common/default.jpg)
RF ATTENUATOR 7DB SMA MODULERF Attenuato...
![ATT-0276-07-SMA-02 Allicdata Electronics](https://files.allicdata.com/upload/common/default.jpg)