Allicdata Part #: | Z8583-ND |
Manufacturer Part#: |
D6F-20A61-000 |
Price: | $ 150.32 |
Product Category: | Sensors, Transducers |
Manufacturer: | Omron Electronics Inc-EMC Div |
Short Description: | AIRFLOW SENSOR MEMS 20L/MIN |
More Detail: | Air Flow Sensor 0 ~ 20 LPM Thermoplastic resin |
DataSheet: | D6F-20A61-000 Datasheet/PDF |
Quantity: | 3 |
1 +: | $ 136.65300 |
5 +: | $ 128.11200 |
10 +: | $ 123.84200 |
25 +: | $ 119.57100 |
50 +: | $ 117.43600 |
Series: | D6F |
Part Status: | Active |
Sensing Range: | 0 ~ 20 LPM |
Flow Sensor Type: | Air |
Voltage - Input: | 10.8 V ~ 26.4 V |
Port Size: | -- |
Switch Function/Rating: | -- |
Material - Body: | Thermoplastic resin |
Operating Temperature: | -10°C ~ 60°C (TA) |
Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us: sales@allicdata.com
Flow sensors are used to measure the rate of flow of a liquid or a gas. The D6F-20A61-000 is one of the most popular flow sensors. It is based on the principle of variable force balance, whereby a beam is attached to the flow tube and is acted on by the variable force of the flow stream. This force is used to calculate the flow rate.
The D6F-20A61-000 flow sensor detects variations in mass flow through an integrated orifice tube in front of the sensor. It does not need to be in contact with the fluid, but instead uses a small air gap between the sensor and the tube to measure the flow rate. This air gap is important for reliable operation, as it shields the moving parts from the abrasive nature of the fluid.
The D6F-20A61-000 flow sensor is designed for use in high-pressure applications, where a wide range of flow rates are encountered. It is capable of measuring flow rates from 0-100 m3/h with a minimum pressure drop of 0.1 kPa. The output signal of this sensor is an electrical signal proportional to the flow rate. It has an operating temperature range of -40°C to +120°C.
The D6F-20A61-000 flow sensor is a highly reliable and accurate device, and is widely used in a variety of industrial applications, such as oil and gas, petrochemical, pharmaceutical, power generation and automotive. It is especially suitable for use in closed-loop control systems in which the flow rate must be tightly monitored and controlled. It is also ideal for many fluid transfer applications, such as air, water and fuel.
The working principle of the D6F-20A61-000 flow sensor is based on the variable force equilibrium of the beam installed in the flow tube. The beam is subject to the varying force of the flow stream and, based on this force, the flow rate is then calculated. The sensor consists of two main components: the movable part, which is mounted on the beam and responds to the dynamic pressure droop, and the non-movable part, which acts as a counterweight and reference point.
The internal control circuits of the D6F-20A61-000 flow sensor continually monitor the input signal and adjust the output voltage or current according to the measured flow rate. This allows the sensor to operate within the specified flow ranges without the need for manual adjustments. The low power consumption of this device makes it very suitable for portable applications.
The D6F-20A61-000 flow sensor is an effective and reliable device for measuring flow rates of liquids and gases in a variety of industries. It is easy to install and maintain and is capable of operating within a wide range of flow rates and temperatures. Its low power consumption, rugged design and high accuracy make it an excellent choice for many flow measurement applications.
The specific data is subject to PDF, and the above content is for reference
MEMS FLOW AND PRESSURE MODULEGas Flow Se...
SENSOR AIRFLOW 1.0 SLPMAir Flow Sensor 1...
FLOW SWITCH--MR-W1-PFlow Sensor 1 ~ 30 L...
G5/4" WATER FLOW SENSORLiquid Flow Senso...
G1" WATER FLOW SENSORLiquid Flow Sensor ...
FLOW SENSOR MEMSGas Flow Sensor 0 ~ 2 LP...