Allicdata Part #: | VE-J6W-MY-ND |
Manufacturer Part#: |
VE-J6W-MY |
Price: | $ 0.00 |
Product Category: | Power Supplies - Board Mount |
Manufacturer: | Vicor Corporation |
Short Description: | DC DC CONVERTER 5.5V 50W |
More Detail: | Isolated Module DC DC Converter 1 Output 5.5V 9... |
DataSheet: | VE-J6W-MY Datasheet/PDF |
Quantity: | 1000 |
1 +: | 0.00000 |
Current - Output (Max): | 9.09A |
Base Part Number: | VE-J6W |
Size / Dimension: | 2.28" L x 2.40" W x 0.50" H (57.9mm x 70.0mm x 12.7mm) |
Package / Case: | Half Brick |
Mounting Type: | Through Hole |
Efficiency: | 90% |
Operating Temperature: | -55°C ~ 100°C |
Features: | OCP, SCP |
Applications: | ITE (Commercial) |
Voltage - Isolation: | 3kV |
Power (Watts): | 50W |
Series: | VE-J00™ |
Voltage - Output 3: | -- |
Voltage - Output 2: | -- |
Voltage - Output 1: | 5.5V |
Voltage - Input (Max): | 400V |
Voltage - Input (Min): | 200V |
Number of Outputs: | 1 |
Type: | Isolated Module |
Part Status: | Active |
Packaging: | Bulk |
Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us: sales@allicdata.com
DC DC converters, such as the VE-J6W-MY, are a type of electronic device that converts a DC voltage or current source from one level to a different voltage or current level. This type of converter is commonly used in applications where the source of power needs to be isolated from the load, or where the output voltage needs to be higher or lower than the input voltage. This type of converters can be used for applications such as power supplies, battery chargers, and motor drives.
The VE-J6W-MY is a DC-DC converter with wide input voltage range. It has an input voltage range of 10V to 48V and an output voltage range of 1.8V to 24V. It can deliver 10A of power with 90~96.5% efficiency and operate at switching frequency that ranges from 100kHz to 1MHz. The VE-J6W-MY also has built in under-voltage protection to ensure the reliability of the system.
The VE-J6W-MY uses a buck topology which is a step-down voltage regulator. In this type of converter, an inductor is placed between the input voltage source and the output voltage. When the switch is driven by a control circuit, the current in the inductor charges and then discharges to drive the load. The inductor stores the energy from the input voltage and the output voltage is controlled by the duty cycle, the switching frequency and the inductance of the inductor. This type of converter is usually used in applications where an isolated power source is required or the output voltage needs to be higher than the input voltage.
The VE-J6 W-MY can be used in a variety of applications. It can be used as a power supply for electronic equipment, medical devices, instrumentation, measurement systems, RF and microwave equipment, solar and wind power conversion applications and other industrial applications. It can be used for motor control and battery charging applications as well.
The VE-J6W-MY is a reliable and efficient DC-DC converter that can be used in a variety of applications. It has wide input voltage range, high efficiency and excellent protection features. The buck topology used in this converter offers cost-effective and flexible solutions for step-down voltage regulation in industrial, commercial and consumer applications.
The specific data is subject to PDF, and the above content is for reference
DC DC CONVERTER 12V 240WIsolated Module ...
DC DC CONVERTER 12V 240WIsolated Module ...
DC DC CONVERTER 12V 240WIsolated Module ...
DC DC CONVERTER 1.8V 120WIsolated Module...
DC DC CONVERTER 1.8V 120WIsolated Module...
DC DC CONVERTER 1.8V 120WIsolated Module...