VE-JTM-CW-F3

Current - Output (Max):	10A
Base Part Number:	VE-JTM
Size / Dimension:	2.28" L x 1.80" W x 0.79" H (57.9mm x 45.7mm x 20.0mm)
Package / Case:	Half Brick
Mounting Type:	Through Hole
Efficiency:	90%
Operating Temperature:	-25°C ~ 100°C
Features:	OCP, SCP
Applications:	ITE (Commercial)
Voltage - Isolation:	3kV
Power (Watts):	100W
Series:	VE-J00™
Voltage - Output 3:	--
Voltage - Output 2:	--
Voltage - Output 1:	10V
Voltage - Input (Max):	160V
Voltage - Input (Min):	66V
Number of Outputs:	1
Type:	Isolated Module
Part Status:	Active
Packaging:	Bulk

Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us:   sales@allicdata.com

DC DC Converters

DC-DC converters are used to couple dc input sources together, such as solar panels, LDOs, and fuel cells. They are used to provide a uniform output voltage or current, or an adjustable output voltage and current, from a variety of input sources. These converters are used for a variety of applications, like powering remote equipment, battery management systems, and motor control. The main types of DC-DC converters include isolated converters, forward converters, and flyback converters. Isolated converters are used to provide a regulated output from an unregulated input source while providing galvanic isolation between the input and output. Forward converters provide a high-level regulated output voltage from an unregulated input source, and are capable of handling high power levels. Flyback converters are more efficient than the other two types, and can provide a range of output voltages from a single input source. VE-JTM-CW-F3 is a type of DC-DC converter. It is a non-isolated boost/buck DC-DC Synchronous Step Down/Up converter module. This module can be used for any application where input and output voltage need to be adjusted. It can take any voltage input from 4.5 to 28V and provides an output of 0.5V to output voltage (Vin). This converter module is based on the Texas Instruments TPS56420 step-down and step-up DC-DC controller and is provided in an easy to install surface mount package. The VE-JTM-CW-F3 is designed for switching frequency up to 500 KHz and can provide a maximum output of 3 amps. The working principle of the VE-JTM-CW-F3 is based on current-mode control. The module employs an internal comparator to regulate the output voltage by comparing the feedback capacitor voltage and reference voltage. An external feedback resistor is used to set the output voltage. When the output voltage is lower than the set target, the Pulse Width Modulator (PWM) comparator is set to output a high-level signal to the power switch. Then the power switch is enabled and current is supplied to the inductor, thus increasing the current in the inductor. At the same time, the output capacitor charges with the supplied current to increase the output voltage. During the other half-cycle, the output of the PWM comparator is pulled low, and the current from the inductor is discharged to keep the output voltage constant. The VE-JTM-CW-F3 is a versatile device, and can be used in a variety of applications. It can be used in industrial, automotive, consumer, renewable energy, and medical applications. It can be used for LED drivers, battery powered equipment, and other power conversion applications. It is a cost-effective choice for small power applications and is designed for low-cost, low-power, and high-efficiency operation. The VE-JTM-CW-F3 is an efficient and reliable DC-DC converter that can provide a consistent and adjustable output voltage or current from a wide range of input sources. It is a cost-effective choice for small power conversion applications, and is designed to operate efficiently in a variety of environments and applications.

The specific data is subject to PDF, and the above content is for reference