ACPL-W611-000E

Data Rate:	10MBd
Supplier Device Package:	6-SO
Package / Case:	6-SOIC (0.268", 6.80mm Width)
Mounting Type:	Surface Mount
Operating Temperature:	-40°C ~ 100°C
Voltage - Supply:	4.5 V ~ 5.5 V
Current - DC Forward (If) (Max):	20mA
Voltage - Forward (Vf) (Typ):	1.5V
Rise / Fall Time (Typ):	24ns, 10ns
Propagation Delay tpLH / tpHL (Max):	75ns, 75ns
Series:	--
Current - Output / Channel:	50mA
Output Type:	Open Collector, Schottky Clamped
Input Type:	DC
Common Mode Transient Immunity (Min):	10kV/µs
Voltage - Isolation:	5000Vrms
Inputs - Side 1/Side 2:	1/0
Number of Channels:	1
Part Status:	Active
Packaging:	Tube

Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us:   sales@allicdata.com

ACPL-W611-000E Application Field and Working PrincipleOptoisolators - Logic Output, such as the ACPL-W611-000E, are electronic components that are used to provide electrical isolation between two circuits. In other words, they act as a bridge between two circuits that can pass signals without actually connecting the two circuits electrically.The ACPL-W611-000E, manufactured by Avago Technologies, is a very popular optoisolator, and it has many applications. It is used in communications, automation, industrial control, instrumentation, medical devices, consumer electronics, and other electronic hardware. The component is mainly used to control inputs and outputs of digital signals, and also provide protection from ground loops, spikes, and electrical noise.The ACPL-W611-000E is an optocoupler type optoisolator, which is a combination of an infrared LED (infrared light emitting diode) and a phototransistor. The LED can be powered by either a voltage source or a current source and it emits near-infrared radiation. The phototransistor is then connected to the LED in such a way that the LED\'s radiation is detected and amplified by the phototransistor.When a voltage is applied to the LED, the LED emits infrared radiation. This radiation is then collected by the phototransistor, amplified, and used to switch the optoisolator. The ACPL-W611-000E can be used to switch high loads up to 2 Amps, and it can also be used to drive digital logic circuits. The maximum input current is usually 50 and the maximum output current is 2 Amps.When using the ACPL-W611-000E, it is important to make sure that the input voltage is within the specified limits (3.5V - 18V), otherwise the optoisolator may not operate correctly. Additionally, the connections should be made in a signal latching type arrangement, otherwise the optoisolator may not provide the necessary electrical isolation.The ACPL-W611-000E has a wide range of applications. It can be used to switch off low-power circuits, such as alarm systems and motor control circuits. It can also be used to switch on high power circuits, such as lighting systems and solenoid valves. Additionally, the ACPL-W611-000E can be used to extend wire runs, provide protection from ground loops, and safeguard electrical circuits from surges and spikes.In conclusion, the ACPL-W611-000E, a popular form of Optoisolators - Logic Output, is a combination of an infrared LED and a phototransistor that can be used to control inputs and outputs of digital signals, as well as provide protection from ground loops, surges and spikes. It is suitable for a variety of applications, including alarms systems, motor control circuits, lighting systems, and solenoid valves. The input voltage should be within the specified limits and connections should be made in a signal latching type arrangement for the best performance.

The specific data is subject to PDF, and the above content is for reference

Part Number	Manufacturer	Price	Quantity	Description