LTC2634CUD-HZ12#PBF

Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us:   sales@allicdata.com

Data Acquisition - Digital to Analog Converters (DAC) are circuitry used to convert a digital value into an analog voltage or current. The LTC2634CUD-HZ12#PBF is a highly-integrated DAC that includes a 3.2V to 5.5V power supply, output drive stage, and buffer. It can be used for a wide range of applications, including digital feedback systems, support of industrial process control and system calibration. The following outlines the main application fields and working principle of the LTC2634CUS-HZ12#PBF.

Applications of the LTC2634CUD-HZ12#PBF

The LTC2634CUD-HZ12#PBF is a 12-bit resolution, rail-to-rail output, voltage output DAC that can easily interface with a variety of microcontrollers and signal processors. This device is well-suited for a variety of applications, including:

• Analog loop control
• Calibration of position, pressure, or temperature sensors
• Digitally programmable attenuators and filters
• Synthesized waveform generation
• Controlling output current or voltage

The device features up to ±5V output swing and patent-pending devices auto-calibration technology. It can be used in conjunction with any microcontroller or signal processor for efficient control loops.

Working Principle of the LTC2634CUD-HZ12#PBF

The LTC2634CUD-HZ12#PBF is a 12-bit voltage output DAC. The DAC accepts digital input and converts it into an adjustable linear single-ended voltage output. The output voltage can range from 0V to 5V or 0V to -5V, depending on the logic levels of the control inputs. The device also includes a buffer amplifier that can be used to drive a load as small as 500Ω. The data interface of the device consists of five control pins, including the chip select (CS), serial clock (SCK), data-in (DIN), power down (PD), and UDP/DCP (unipolar /bipolar) select. These control pins are used to select the desired output voltage.

The PD pin is used to place the device into a low-power mode when not in use, thus reducing the power consumption of the device. The UDP/DCP pin is used to select either unipolar or bipolar voltage output. The CS pin is used to select the active DAC and initiate data transfer from the DIN to the DAC output registers. The Data Word is written to the corresponding active DAC when the SCK pin is strobed and the data word is latched on the rising edge of the SCK pin. The DAC can be updated with new data Words at any time, depending on the system requirements.

The output voltage of the DAC is determined by the digital code entered into the DAC through the data interface. The DAC also includes an output buffer stage that can drive loads as low as 500Ω. The buffer can be configured as a unity-gain buffer or configured with a gain of approximately 2, 5, or 10. The output buffer can be bypassed, allowing the LTC2634CUD-HZ12#PBF to drive a load directly.

Conclusion

The LTC2634CUD-HZ12#PBF is a 12-bit resolution, rail-to-rail output, voltage output DAC that can easily interface with a variety of microcontrollers and signal processors. It features up to ±5V output swing and patent-pending devices auto-calibration technology. The device can be used for a wide range of applications, including analog loop control, support of industrial process control, and system calibration. Its data interface consists of five pins: the chip select (CS), serial clock (SCK), data-in (DIN), power down (PD), and UDP/DCP (unipolar /bipolar) select. The output voltage of the DAC is determined by the digital code entered into the DAC through the data interface. The output buffer can either be bypassed, giving a direct connection to the output of the DAC, or it can be configured with a gain of 2, 5, or 10 to drive a load of 500Ω.

The specific data is subject to PDF, and the above content is for reference