Allicdata Part #: | MMS005AA-ND |
Manufacturer Part#: |
MMS005AA |
Price: | $ 109.72 |
Product Category: | RF/IF and RFID |
Manufacturer: | Microsemi Corporation |
Short Description: | MMIC ATTENUATOR - DC-40GHZ |
More Detail: | RF Attenuator 17dB 0Hz ~ 40GHz 50 Ohms |
DataSheet: | MMS005AA Datasheet/PDF |
Quantity: | 1000 |
25 +: | $ 99.74020 |
Series: | -- |
Part Status: | Active |
Attenuation Value: | 17dB |
Frequency Range: | 0Hz ~ 40GHz |
Power (Watts): | -- |
Impedance: | 50 Ohms |
Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us: sales@allicdata.com
Attenuators are a type of electronic device used to reduce the amplitude of a signal, usually in terms of voltage, power, or current. The MMS005AA is a type of programmable attenuator designed for high-frequency applications such as radar, communication, and GPS systems. In this article, we’ll take a closer look at the MMS005AA, its application field and working principle.
Overview of the MMS005AA
The MMS005AA is a high-frequency programmable attenuator used in various applications needing the ability to adjust the signal amplitude. It is designed to operate over a frequency range of 0.5 GHz to 8 GHz at voltages from -75 to +7.5 dBm. The device has an insertion loss of < 10 dB and a typical attenuation range of 0.1 to 30 dB. It is designed to be used with a low-power source (the maximum power input is usually less than 150 mW) and is capable of operating up to a maximum attenuation of 60 dB. In addition, the device features high linearity, low distortion, and good stability regardless of the operating conditions. It is constructed using gallium arsenide technology, which ensures high accuracy and reliability.
Application Field of the MMS005AA
The MMS005AA is primarily used in communication systems, radar systems, GPS systems, navigation systems, and other types of high-frequency applications. It is designed to reduce the signal amplitude of high-frequency signals traveling over these systems and ensure that the signals reach their intended destination without distortion or interference. Additionally, the device can be used in test and measurement applications where attenuation is needed to prevent excessive power levels from damaging the test gear.
Working Principle of the MMS005AA
The MMS005AA operates on a simple principle. It is composed of a pair of switches, each connected to a terminal. When a signal is applied to the device, the switches open and close in a repetitive cycle that creates a controlled attenuation of the signal. This cycle has two states, a conductive state in which the switches are closed and the signal is attenuated, and a non-conductive state in which the switches are open and the signal passes through the device without being attenuated.
When the signal is in the non-conductive state, it passes through the device\'s resistors and is attenuated by a certain amount. The amount of attenuation is proportional to the size of the resistors. By adjusting the size of the resistors, or by splicing different resistors together, the device can create different levels of attenuation.
Conclusion
The MMS005AA is a programmable attenuator designed for high-frequency applications. It is composed of a pair of switches that create a repetitive cycle of attenuation when a signal is applied to the device. The amount of attenuation can be adjusted by changing the size of the resistors or by splicing different resistors together. The device is commonly used in communication systems, radar systems, GPS systems, navigation systems, and other types of high-frequency applications.
The specific data is subject to PDF, and the above content is for reference
RF ATTENUATOR 1DB-31DB 24VFQFNRF Attenua...
RF ATTENUATOR 1DB-60DB 50OHM TNCRF Atten...
RF ATTENUATOR 1DB SMA MODULERF Attenuato...
RF ATTENUATOR 2DB 50OHM 1206RF Attenuato...
RF ATTENUATOR 6DB 50OHM SMARF Attenuator...
RF ATTENUATOR 7DB SMA MODULERF Attenuato...