Allicdata Part #: | 939-1020-ND |
Manufacturer Part#: |
P522303-01 |
Price: | $ 0.00 |
Product Category: | RF/IF and RFID |
Manufacturer: | Ethertronics/AVX |
Short Description: | CELL DEMO BOARD 5-BAND 50X110MM |
More Detail: | N/A |
DataSheet: | P522303-01 Datasheet/PDF |
Quantity: | 1000 |
1 +: | 0.00000 |
Series: | -- |
Part Status: | Obsolete |
Type: | Antenna |
Frequency: | 850MHz, 900MHz, 1.8GHz, 1.9GHz, 2.1GHz |
For Use With/Related Products: | P522303 |
Supplied Contents: | Board(s) |
Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us: sales@allicdata.com
RF Evaluation and Development Kits, Boards make use of the P522303-01 component, an integrated single-chip antenna coupled broadband front end module, to facilitate wireless design engineers with the development of high performance systems. It offers integrated single-chip antenna coupled broadband RF front end with an integrated, ultra low power, low noise amplifier (LNA), mixer, and passive components. The P522303-01 module serves as an input for an RF amplifier to transmit the signal up to frequencies of 6GHz, while also receiving down to the non-directional frequencies.
The integrated antenna coupled front end module enables engineers to design high performance transceivers with low power consumption, and improved dynamic range and sensitivity. In a nutshell, the P522303-01 component offers an extremely wide dynamic range and linearity of the RF signal, a low noise figure, and a low distortion profile. The P522303 is designed to provide superior performance in a wide range of applications.
The P522303-01 application field expands to many different industries across different workflows such as general wireless communications, urban or military communication networks, point-to-point or multi-point communications, audio and video streaming, navigation and much more. It can be used in telecommunication systems, automotive systems, satellite communication systems, and medical devices.
The working principle of the P522303-01 component is based on its RF signal mixer, which utilizes an array of mixer diodes, tuned capacitor and inductor networks to provide efficient signal mixing required in part of the system’s firmware or software. These relative components need to be matched perfectly to the designers’ specification in order to ensure optimum performance. The output signal is a modulation ratio line composed of a low pass filter and a high pass filter, which is applied to the circuit to determine the appropriate frequency to which the signal needs to be tuned. The basic components of the P522303-01 module are the inductors, capacitors, and mixers, which act as a mixer stage and provide signal mixing. The transistor switch is also part of the module and helps to amplify the signal strength.
The P522303-01 is based on a highly linear single-ended active mixer, where a voltage controlled oscillator fed with a low-frequency signal is used to drive the two high-frequency ports. The technique used for acquiring the frequency range is to adjust the voltage into the oscillator by using an external amplifier, which is connected to a power supply.
The P522303-01 is configured in a digital signal path, allowing up to 30 MHz (LPF) low pass filtering and 130 MHz (HPF) high pass filtering. It is also equipped with an integrated high linearity switch, allowing up to 24dB of isolation within the gain block. The component is highly efficient, offering up to 10 dB noise figure with less than 0.7nV of noise due to its high dynamic range. The device is also well integrated, requiring just 4 voltage rails for operation, eliminating the need for separate low noise approaches.
In summary, the P522303-01 is a great module for integrating high-performance transceivers with a very wide dynamic range and linearity of the RF signal. It offers improved dynamic range, sensitivity and low noise figure, as well as a high linearity switch for isolation within the gain block. The device is highly efficient, requiring just 4 voltage rails, and supports multiple RF frequency operations, allowing designers to easily design high performance, low power transceivers for a wide range of applications.
The specific data is subject to PDF, and the above content is for reference
Part Number | Manufacturer | Price | Quantity | Description |
---|
P522-006 | Tripp Lite | 0.0 $ | 1000 | CABLE EXTNSION CGA/EGA DB... |
ET4-P5228 | SICK, Inc. | 48.51 $ | 1000 | SEN PHT PNP LO M12 155 MM |
ZT2-P5228 | SICK, Inc. | 44.63 $ | 1000 | PNP LO M12 155 MM IR |
ET3-P5228 | SICK, Inc. | 47.54 $ | 1000 | SEN PHT PNP LO M12 155 MM |
P522303-01 | Ethertronics... | 0.0 $ | 1000 | CELL DEMO BOARD 5-BAND 50... |
P522304 | Ethertronics... | 2.45 $ | 14560 | CELL ANTENNA 5-BAND 35X9X... |
P522309 | Ethertronics... | 4.35 $ | 2568 | RF ANT PRESTTA PENTA U.FL... |
P522304-02 | Ethertronics... | 14.14 $ | 18 | CELL ANTENNA DEMO BOARD 5... |
ZT1-P5221 | SICK, Inc. | 56.27 $ | 15 | SEN PHT LO PNP 155MM M12 ... |
P522303 | Ethertronics... | 3.56 $ | 5770 | CELL ANTENNA 5-BAND 42X12... |
P522304-01 | Ethertronics... | 10.5 $ | 1000 | CELL ANTENNA DEMO BOARD 5... |
P522306 | Ethertronics... | 2.45 $ | 1000 | RF ANT PRESTTA PENTA-BAND... |
ZT2-P5221 | SICK, Inc. | 56.27 $ | 1000 | LO RA 150MM PGL M12 155MM |
JN5179 USB DONGLE FOR ZIGBEE
EVAL BOARD FOR SKY67159-396LF
EVAL BOARD FOR MICRF219A
EVAL BOARD FOR HMC468ALP3
EVAL BOARD NESG250134
BOARD EVAL HMC541LP3E