Allicdata Part #: | 1EN537-6-ND |
Manufacturer Part#: |
1EN537-6 |
Price: | $ 0.00 |
Product Category: | Switches |
Manufacturer: | Honeywell Sensing and Productivity Solutions |
Short Description: | SWITCH LIMIT PB PNL MT DPDT 4A |
More Detail: | N/A |
DataSheet: | 1EN537-6 Datasheet/PDF |
Quantity: | 1000 |
1 +: | 0.00000 |
Series: | * |
Part Status: | Obsolete |
Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us: sales@allicdata.com
Snap action, limit switches are most often seen in use today to prevent excessive power from being supplied to a device. They are used to detect when certain conditions have been met, often from excessive pressure, temperature, or voltage. The 1EN537-6 limit switch is a general-purpose, thermal-resetting limit switch that is well suited for many applications. Typically, the switch is mounted in a panel or cylinder and its purpose is to permit a controlled amount of energy to send an alarm signal or open circuit when the thermal limit is reached.
The 1EN537-6 limit switch is made up of two primary components: the body and the actuator. The body of the switch is the main frame that attaches the device to the intended surface. The actuator is a set of pins that are activated when a specific force is applied to it. When the force is exceeded, the actuator opens, allowing a relay or other electrical device to tell the system to shut off. This feature is also known as a "thermal-resetting" limit switch as the pins are reset each time the switch is triggered.
The 1EN537-6 limit switch can be used in a variety of applications, from limiting the amount of power that can be delivered to a device, to detecting a dangerous level of pressure, temperature or voltage. Most commonly, the switch is used in industrial or commercial applications, such as in HVAC systems, pumps, and other heavy-duty equipment.
In order to use the 1EN537-6 limit switch, a power load must be connected to the switch. This can be done either directly, or by using a relay. The power load is then connected to the device that the limit switch will be controlling. If a relay is used, it must be properly configured to disconnect the load when the limit switch is triggered.
Once the switch is connected to the device, it is set to the desired settings. This typically involves setting the limit switch\'s trip point, or the point where the relay will be triggered. The switch will then begin to monitor the conditions and respond when the set trip point is reached.
The 1EN537-6 limit switch is a reliable, efficient, and cost effective way to ensure that your power-heavy equipment is functioning correctly. It is easy to install and configure, and can provide an added layer of safety to ensure that your equipment is operating properly.
The specific data is subject to PDF, and the above content is for reference
Part Number | Manufacturer | Price | Quantity | Description |
---|
1EN531-1B | Honeywell Se... | 0.0 $ | 1000 | SWITCH LIMIT PB PNL MT SP... |
1EN537-6 | Honeywell Se... | 0.0 $ | 1000 | SWITCH LIMIT PB PNL MT DP... |
1EN543-R | Honeywell Se... | 0.0 $ | 1000 | SWITCH LIMIT PB PNL MT DP... |
1EN51-6 | Honeywell Se... | 245.04 $ | 4 | SWITCH SNAP ACTION SPDTX2... |
1EN51-RB | Honeywell Se... | 0.0 $ | 1000 | SEALED AERO SWITCH |
1EN51-6B | Honeywell Se... | 0.0 $ | 1000 | ENVIRONMENTALLY SEALED LI... |
1EN51-1B | Honeywell Se... | 502.94 $ | 1000 | SWITCH LIMIT PB PNL MT DP... |
1EN51-S | Honeywell Se... | 268.66 $ | 1000 | ENVIRONMENTALLY SEALED LI... |
1EN564-2B | Honeywell Se... | 282.09 $ | 1000 | SWITCH LIMIT PB PNL MT SP... |
1EN554-6 | Honeywell Se... | 304.55 $ | 1000 | SWITCH LIMIT PB PNL MT DP... |
1EN578-6 | Honeywell Se... | 324.49 $ | 1000 | SWITCH LIMIT PB PNL MT DP... |
1EN557 | Honeywell Se... | 353.85 $ | 1000 | SEALED AERO SWITCH |
1EN577-RB | Honeywell Se... | 679.41 $ | 1000 | SWITCH LIMIT PB PNL MT SP... |
LIMIT SWITCH
LIMIT SWITCH ROLLER LEVER LED
SWITCH SNAP ACTION
SWITCH SNAP ACTION
SEALED AERO SWITCH
SWITCH SNAP ACT SPST-NO 16A 125V