DSPIC33FJ06GS202T-I/SO

Program Memory Type:	FLASH
Base Part Number:	DSPIC33FJ06GS202
Supplier Device Package:	28-SOIC
Package / Case:	28-SOIC (0.295", 7.50mm Width)
Operating Temperature:	-40°C ~ 85°C (TA)
Oscillator Type:	Internal
Data Converters:	A/D 6x10b, D/A 2x10b
Voltage - Supply (Vcc/Vdd):	3 V ~ 3.6 V
RAM Size:	1K x 8
EEPROM Size:	--
Series:	dsPIC™ 33F
Program Memory Size:	6KB (6K x 8)
Number of I/O:	21
Peripherals:	Brown-out Detect/Reset, POR, PWM, WDT
Connectivity:	I²C, IrDA, LINbus, SPI, UART/USART
Speed:	40 MIPs
Core Size:	16-Bit
Core Processor:	dsPIC
Part Status:	Active
Packaging:	Tape & Reel (TR)

Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us:   sales@allicdata.com

Introduction

The DSPIC33FJ06GS202T-I/SO is a 16-bit Digital Signal Controller (DSC) with integrated features that enable easy implementation of real-time control and signal processing applications. It is part of the Microchip’s extensive range of Digital Signal Controllers and is designed to provide the highest level of performance and features while using minimum power. The device integrates an advanced 16-bit cpu, a 12-bit Analog-to-Digital Converter (ADC) and several peripherals for an attractive single-chip digital signal processing solution. In addition, it has built-in DSP instructions and offers the advantages of lower cost, smaller board area, and a saving of resources when compared to traditional microcontrollers. The digital signal controller featured in the DSPIC33FJ06GS202T-I/SO combines the most advanced signal-processing technologies available with a reduced system cost perspective. It is a very powerful microcontroller that is capable of high-speed data and signal processing, as well as providing a wide range of integrated peripherals and functions. This device can process data at higher speeds, consume less power, and offer enhanced real-time control and signal-processing features.

Application Field

The DSPIC33FJ06GS202T-I/SO is designed to be used in a variety of control and signal-processing applications. It is suitable for measuring and monitoring, automation, motor control and drive, process control, data acquisition, instrumentation, and testing. Its wide range of analog and digital peripherals enables a wide range of signals and parameters to be measured, monitored, and controlled. The 16-bit Digital Signal Controller (DSC) is capable of delivering high-performance analog, signal-processing, and control capabilities all on one low-power integrated device. It can be used for control applications such as closed-loop control systems, signal-processing applications such as filters and digital signal processing (DSP), and communication applications such as messaging and data transfer.The DSPIC33FJ06GS202T-I/SO is also designed for low-power computing applications, allowing the processor to operate at lower operating voltage and frequency levels. This device can be used in medical devices, consumer electronics, automotive, and other embedded systems.

Working Principle

The DSPIC33FJ06GS202T-I/SO is a member of the 16-bit Digital Signal Controller (DSC) family. The DSC core is based on the RISC-based architecture of the MIPS32 instruction set. All instructions are 16-bits wide and there are two banks of 32 registers, each bank having 32 general-purpose registers. The instruction fetch unit includes a program counter and memory demapping logic, and the instruction decode unit includes a control logic unit. The DSPIC33FJ06GS202T-I/SO\'s sub-system consists of an ADC peripheral, four 12-bit digital-to-analog converters (DACs), an analog filter, six 16-bit timers, four advanced interrupt controllers, two cycle counters, one serial peripheral interface (SPI), three universal asynchronous receiver-transmitters (UARTs), and one I2C module. The device also features a program memory protection unit, parallel slave port (PSP), and direct memory access (DMA) controller. With its comprehensive range of analog and digital peripherals, the device can interface with a variety of onboard as well as external peripherals. The DSPIC33FJ06GS202T-I/SO can be programmed in assembly, C and other high-level languages. It can also be used in conjunction with external hardware such as an LCD module, keypad, and sensors for embedded system applications.

Conclusion

The DSPIC33FJ06GS202T-I/SO is an economical and powerful 16-bit Digital Signal Controller (DSC) suitable for various control and signal processing applications. It combines the most advanced signal processing technologies and peripherals in a single device and offers a flexible, low-cost solution for many embedded applications. With its robust architecture and large number of peripherals, it is a valuable choice for embedded system designers.

The specific data is subject to PDF, and the above content is for reference

Part Number	Manufacturer	Price	Quantity	Description