HIN232EIBN-T

Series:	--
Packaging:	Tape & Reel (TR)
Part Status:	Obsolete
Type:	Transceiver
Protocol:	RS232
Number of Drivers/Receivers:	2/2
Duplex:	Full
Receiver Hysteresis:	500mV
Data Rate:	230kbps
Voltage - Supply:	4.5 V ~ 5.5 V
Operating Temperature:	-40°C ~ 85°C
Mounting Type:	Surface Mount
Package / Case:	16-SOIC (0.154", 3.90mm Width)
Supplier Device Package:	16-SOIC
Base Part Number:	HIN232E

Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us:   sales@allicdata.com

Introduction

The HIN232EIBN-T is an integrated circuit (IC) typically used as a transceiver to enable serial communication in applications such as robotic control, industrial automation, and biomedicine. This device converts a high-speed serial stream into up to 4 parallel data and control signals, and vice-versa, using one low-cost package. Additionally, it supports a wide range of data rates from 16 Mb/s to 96 Mb/s, with a typical latency of less than 50 ns. By connecting remote equipment with HIN232EIBN-T transceivers, it is possible to reduce system wiring costs, complexity, and space requirements while providing the performance necessary for the operation of modern technologies.

Application Field of HIN232EIBN-T

HIN232EIBN-T transceivers are widely used in a variety of industries, particularly in robotics and industrial automation. In robotics, the transceiver can be used for the communication between the arms and chassis of a robot, providing a low-cost, low-latency connection. The transceiver can also be used for the communication between a robotic controller and motors, allowing for more precise and efficient operation. In industrial automation, the HIN232EIBN-T transceiver is often used for industrial control systems and distributed process control applications. It can be used to replace manual control systems, providing a low-cost, efficient, and reliable system. It can also be used in distributed process control applications, allowing for the remote monitoring and managing of processes in multiple properties. Additionally, the transceiver is used in biomedicine, where it is used to allow multiple sensors to be connected and monitored remotely.

Working Principle of HIN232EIBN-T

The HIN232EIBN-T is an integrated circuit (IC) and functions as a transceiver. It features four channels-two receive (Rx) and two transmit (Tx)-and each can support up to 96 megabits per second (Mbps) data transfer speeds. The device functions by converting a serial stream of high-speed data into four parallel data and control signals-two for the transmitter and two for the receiver. The serial data is scrambled and encoded before being sent over the channel, and then decoded and descrambled at the receiving end. The transceiver is equipped with a parallel bus interface, allowing for the connection to a wide variety of devices.When transmitting data, the HIN232EIBN-T transceiver first converts the serial data stream into parallel data and control signals. This can be accomplished by using a Pulse Width Modulation (PWM) or a Time Division Multiplexing (TDM) technique. The transceiver then scrambles the data and encodes it according to a specified protocol, such as Ethernet or IEEE 802.1. Finally, the device transmits the encoded data over the channel to the receiver.At the receiving end, the HIN232EIBN-T transceiver decodes the received data and descrambles it before converting it back into the serial data stream. Additionally, the device is capable of regenerating data that has been corrupted due to transmission errors. This is done using an error-detection and correction (EDAC) method, which is based on a Cyclic Redundancy Check (CRC). The CRC allows the device to detect and correct any errors that may have occurred during the transmission of data.

Conclusion

The HIN232EIBN-T transceiver is an integrated circuit (IC) that is typically used for serial communication in a variety of applications. The device is capable of transmitting and receiving data at up to 96 Mbps, with a typical latency of less than 50 ns. It is also equipped with a parallel bus interface that allows for the connection to a wide variety of devices, such as robotic arms, industrial control systems, and distributed process control applications. Additionally, the device can be used to regenerate data that has been corrupted due to transmission errors. Overall, the HIN232EIBN-T transceiver is a useful and versatile asset in the field of serial communication.

The specific data is subject to PDF, and the above content is for reference

Part Number	Manufacturer	Price	Quantity	Description