PIC18F4580-I/PT

Due to market price fluctuations,if you need to purchase or consult the price.You can contact us or emial to us:   sales@allicdata.com

1. Special Microcontroller Features

    1. C Compiler Optimized Architecture with Optional Extended Instruction Set

    2. 100,000 Erase/Write Cycle Enhanced Flash Program Memory Typical

    3. 1,000,000 Erase/Write Cycle Data EEPROM Memory Typical

    4. Flash/Data EEPROM Retention: > 40 Years

    5. Self-Programmable under Software Control

    6. Priority Levels for Interrupts

    7. 8 x 8 Single-Cycle Hardware Multiplier

    8. Extended Watchdog Timer (WDT):

        - Programmable period from 41 ms to 131s

    9. Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via Two Pins

  10. In-Circuit Debug (ICD) via Two Pins

  11. Wide Operating Voltage Range: 2.0V to 5.5V

2. Peripheral Highlights

    1. High-Current Sink/Source 25 mA/25 mA

    2. Three External Interrupts

    3. One Capture/Compare/PWM (CCP) module

    4. Enhanced Capture/Compare/PWM (ECCP) module (40/44-pin devices only):

        - One, two or four PWM outputs

        - Selectable polarity

        - Programmable dead time

        - Auto-shutdown and auto-restart

    5. Master Synchronous Serial Port (MSSP) module Supporting 3-Wire SPI (all 4 modes) and I2C™ Master and Slave modes

    6. Enhanced Addressable USART module

        - Supports RS-485, RS-232 and LIN/J2602

        - RS-232 operation using internal oscillator block

        - Auto-wake-up on Start bit

        - Auto-Baud Detect

    7. 10-Bit, up to 11-Channel Analog-to-Digital Converter (A/D) module, up to 100 ksps

        - Auto-acquisition capability

        - Conversion available during Sleep

    8. Dual Analog Comparators with Input Multiplexing

3. Power-Managed Modes

    1. Run: CPU on, Peripherals on

    2. Idle: CPU off, Peripherals on

    3. Sleep: CPU off, Peripherals off

    4. Idle mode Currents Down to 6.1 μA Typical

    5. Sleep mode Current Down to 0.2 μA Typical

    6. Timer1 Oscillator: 1 μA, 32 kHz, 2V

    7. Watchdog Timer: 1.7 μA

    8. Two-Speed Oscillator Start-up

4. Flexible Oscillator Structure

    1. Four Crystal modes, up to 40 MHz

    2. 4x Phase Lock Loop (PLL) – Available for Crystal and Internal Oscillators)

    3. Two External RC modes, up to 4 MHz

    4. Two External Clock modes, up to 40 MHz

    5. Internal Oscillator Block:

        - Fast wake from Sleep and Idle, 1 μs typical

        - 8 user-selectable frequencies, from 31 kHz to 8 MHz

        - Provides a complete range of clock speeds,from 31 kHz to 32 MHz when used with PLL

        - User-tunable to compensate for frequency drift

    6. Secondary Oscillator using Timer1 @ 32 kHz

    7. Fail-Safe Clock Monitor

        - Allows for safe shutdown if peripheral clock stops

5. ECAN Technology Module Features

    1. Message Bit Rates up to 1 Mbps

    2. Conforms to CAN 2.0B Active Specification

    3. Fully Backward Compatible with PIC18XXX8 CAN modules

    4. Three Modes of Operation:

        - Legacy, Enhanced Legacy, FIFO

    5. Three Dedicated Transmit Buffers with Prioritization

    6. Two Dedicated Receive Buffers

    7. Six Programmable Receive/Transmit Buffers

    8. Three Full 29-Bit Acceptance Masks

    9. 16 Full 29-Bit Acceptance Filters w/Dynamic Association

  10. DeviceNet™ Data Byte Filter Support

  11. Automatic Remote Frame Handling

  12. Advanced Error Management Features

6. Pin configuration