PIC32MK0512GPD064-I/PT

Due to market price fluctuations,if you need to purchase or consult the price.You can contact us or emial to us:   sales@allicdata.com

1. Working conditions: 2.3V to 3.6V

    1. -40ºC to +85ºC, DC to 120 MHz

    2. -40ºC to +125ºC, DC to 80 MHz

2. Core: 120 MHz (up to 198 DMIPS)

    1. MIPS32® microAptiv™ MCU core with floating point unit

    2. microMIPS™ mode can reduce code size by up to 40%

    3. DSP enhanced core:

        - Four 64-bit accumulators

        - Single cycle MAC, saturation and fractional math

    4. Code efficient (C and assembly) architecture

    5. Two 32-bit core register files to reduce interrupt latency

3. Clock Management

    1. 8 MHz ±4% (FRC) internal oscillator -40ºC to +85ºC

    2. Programmable PLL and oscillator clock source:

        - HS and EC clock modes

    3. 32 kHz internal low-power RC oscillator (LPRC)

    4. Independent external low-power 32 kHz crystal oscillator

    5. Fail Safe Clock Monitor (FSCM)

    6. Independent watchdog timer (WDT) and dead timer (DMT)

    7. Quick wake up and start

    8. Four fractional clock output (REFCLKO) modules

4. Power Management

    1. Low-power management mode (sleep and idle)

    2. Convergent:

        - Power-on reset (POR) and power-down reset (BOR)

        - Programmable high/low voltage detection (HLVD)

    3. On-board capacitor-less voltage regulator

5. Motor Control PWM

    1. Up to nine PWM pairs

    2. Leading and trailing edge blanking

    3. Dead time for rising and falling edges

    4. Dead zone compensation

    5. 8.33 ns PWM resolution

    6. Clock chopping for high frequency operation

    7. PWM support:

        - DC/DC, AC/DC, inverter, PFC, lighting

        - BLDC, PMSM, ACIM, SRM motors

    8. Choice of 10 fault inputs and 9 current limit inputs

    9. Flexible trigger configuration for ADC triggering

6. Motor encoder interface

    1. Three Quadrature Encoder Interface (QEI) modules:

        - Four inputs: Phase A, Phase B, Home and Index

7. Audio/graphics/touch interface

    1. Up to two I2S audio data communication interfaces

    2. Up to two SPI control interfaces

    3. Programmable master clock:

        - Fractional clock frequency generation

        - Can be adjusted at runtime

8. Unique Features

    1. Permanent non-volatile 4-word unique device serial number

    2. Flash error code correction (ECC)

9. Direct memory access (DMA)

    1. Up to 8 channels with automatic data size detection function

    2. Programmable Cyclic Redundancy Check (CRC)

    3. Up to 64 KB transfer

10. Security features

     1. Advanced memory protection:

         - Peripheral and memory area access control

11. Advanced simulation functions

      1. 12-bit ADC module:

          - The sum of all individual ADCs, 25.45 Msps in 12-bit mode or 33.79 Msps in 8-bit mode

          - 7 independent ADC modules

          - 3.75 Msps per S&H using dedicated DMA

          - Up to 30 analog inputs

      2. Flexible and independent ADC trigger source

      3. Four high-bandwidth operational amplifiers and five comparators

      4. Up to two 12-bit CDACs

      5. Internal temperature sensor ±2ºC accuracy

      6. Capacitive touch distributor (CVD)

12. Communication interface

      1. CAN Flexible Data Rate (CAN FD) module (with dedicated DMA Channel):

          - 2.0B Active supports DeviceNet™ addressing

          - Comply with ISO 11898-1:2015

      2. Up to two UART modules (up to 25 Mbps):

          - Support LIN 2.1 and IrDA® protocol

      3. Two SPI/I2S modules (SPI 50 Mbps)

      4. Two I2C modules supporting SMBus (up to 1 Mbaud)

      5. Peripheral Pin Select (PPS) to enable remappable pin function

13. Timer/Output Compare/Input Capture/RTCC

      1. Up to 9 16-bit or 1 16-bit and 8 32-bit timers/counters for GP and MC devices and two additional QEI 32-bit timers for MC devices

      2. 9 output compare (OC) modules

      3. 9 input capture (IC) modules

      4. PPS to enable feature remapping

      5. Real-time clock and calendar (RTCC) module

14. Input/Output

      1. 5V withstand voltage pin with up to 22 mA source/sink current

      2. Optional internal open drain, pull-up and pull-down

      3. External interrupts on all I/O pins

      4. Five programmable edge/level trigger interrupt pins

15. Qualification and Type B support

      1. AEC-Q100 Class 1 (-40°C to 125°C)

      2. Class B security library

      3. Spare internal oscillator

      4. Clock monitor with backup internal oscillator

      5. Global register lock

16. Debugger development support

      1. Online and application programming

      2. 2-wire or 4-wire MIPS® enhanced JTAG interface

      3. Unlimited software and 12 complex breakpoints

      4. IEEE 1149.2 compatible (JTAG) boundary scan 

      5. Non-intrusive hardware-based instruction tracking

17. Software and tool support

      1. C/C++ compiler with native DSP/decimal support

      2. MPLAB® Harmony integrated software framework

      3. TCP/IP, graphics and mTouch™ middleware

      4. MFi, Android™ and Bluetooth® audio framework

      5. RTOS kernel: Express Logic ThreadX, FreeRTOS™,OPENRTOS®, Micriµm® µC/OS™ and SEGGER embOS®

18. Package overview