Allicdata Part #: | S41S25A-ND |
Manufacturer Part#: |
S41S25A |
Price: | $ 25.67 |
Product Category: | Uncategorized |
Manufacturer: | Altech Corporation |
Short Description: | PIN & SLEEVEPLUG 20A 250VAC 3P 4 |
More Detail: | N/A |
DataSheet: | S41S25A Datasheet/PDF |
Quantity: | 1000 |
1 +: | $ 23.33520 |
Series: | * |
Part Status: | Active |
Due to market price fluctuations, if you need to purchase or consult the price. You can contact us or emial to us: sales@allicdata.com
S41S25A are devices that allow us to measure the amplitude of sinusoidal alternating electrical signals. To measure the signal amplitude accurately, there are a few important steps that must be followed when using any type of signal measurement device. Knowing these steps and how the device works are essential for successfully utilizing the S41S25A.
First, the S41S25A must be connected to the area in which a signal is being measured. To do this a coaxial cable must be used to bridge the device to the signal source. There are two types of coaxial cable that can be used for this purpose—the 49 type and 50 type. The type of cable to use is dependent on the impedance of the signal source.
Once the S41S25A is connected, the next step is to set the gain of the device. This is done with a gain selector switch. There are three possible settings on the device—low gain, high gain, and full scale damping. Setting the gain selector switch to the correct setting is essential for accurate signal measurement.
Next, the power supply for the S41S25A must be set. This is done with a power supply selector switch. There are three settings to choose from on this switch—dc AC,DC and AC ground.
Once these steps have been completed, the measurement can begin. The S41S25A uses a phenomenon called the Beer-Lambert law to measure the amplitude of signals. The Beer-Lambert law states that the intensity of light is inversely proportional to the distance the signal has to travel. So, in terms of signal measurement, the closer the signal is to the S41S25A, the more accurately its amplitude can be measured.
It’s also important to note that the S41S25A is sensitive to noise. In order to reduce noise, it’s important to ensure that the signal source is connected directly to the device. This can be done by using a single-ended or differential cable. Additionally, it is recommended that common-mode filters be used for maximum noise-reduction capabilities.
The S41S25A is an essential tool for accurately measuring the amplitude of sinusoidal alternating electrical signals. Its convenience and accuracy have made it one of the most popular signal measurement devices available today. With the proper setup and use, the S41S25A can be used to accurately measure signal amplitude in a wide range of applications.
The specific data is subject to PDF, and the above content is for reference
Part Number | Manufacturer | Price | Quantity | Description |
---|
S41S05A | Altech Corpo... | 25.67 $ | 1000 | PIN & SLEEVEPLUG20A380440... |
S41S25A | Altech Corpo... | 25.67 $ | 1000 | PIN & SLEEVEPLUG 20A 250V... |
S41S35A | Altech Corpo... | 25.67 $ | 1000 | PIN & SLEEVEPLUG 20A 400V... |
S41S55A | Altech Corpo... | 25.67 $ | 1000 | PIN & SLEEVEPLUG 20A 480V... |
S41S65A | Altech Corpo... | 25.67 $ | 1000 | PIN & SLEEVEPLUG20A120250... |
S41S75A | Altech Corpo... | 25.67 $ | 1000 | PIN & SLEEVEPLUG 20A 600V... |
S41S00A | Altech Corpo... | 17.61 $ | 1000 | PIN & SLEEVEPLUG20A380440... |
S41S20A | Altech Corpo... | 17.61 $ | 1000 | PIN & SLEEVEPLUG 20A 250V... |
S41S30A | Altech Corpo... | 17.61 $ | 1000 | PIN & SLEEVEPLUG 20A 400V... |
S41S50A | Altech Corpo... | 17.61 $ | 1000 | PIN & SLEEVEPLUG 20A 480V... |
S41S60A | Altech Corpo... | 17.61 $ | 1000 | PIN & SLEEVEPLUG20A120250... |
S41S70A | Altech Corpo... | 17.61 $ | 1000 | PIN & SLEEVEPLUG 20A 600V... |
S41S55 | Altech Corpo... | 21.28 $ | 1000 | PIN & SLEEVEPLUG 16A 500V... |
DIODE GENERAL PURPOSE TO220
CB 6C 6#16 SKT RECP
CA08COME36-3PB-44
CA-BAYONET
CB 6C 6#16S SKT PLUG
CAC 3C 3#16S SKT RECP LINE